An Innovative and Reliable Hybrid Cooling Method for Electric Vehicle Motors

Document Type : Original Article

Authors

1 School of Mechanical Engineering, Vellore Institute of Technology Chennai, India

2 Electric Vehicles Incubation, Testing and Research Centre, Vellore Institute of Technology Chennai, India

Abstract

Air, liquid, and oil are commonly used for the cooling of electric vehicle motors. Phase change materials (PCM) are not extensively used apart from electronic components. In general, coolants like air, liquid, and oil were separately used as independent coolants for the motor. In this research, two cooling channels were added to the motor cooling. The liquid is used as a primary coolant, while PCM is used as a secondary coolant. This novel method of cooling helps to keep the bracket temperature under the allowable limit even though the liquid cooling is operating at its lowest operating point. In the study, the primary focus was on the PCM coolant channel by keeping the liquid coolant under one particular operating condition to study the PCM in detail. The thickness of the PCM had an influence on the motor cooling. Three different PCM channels were studied with thicknesses of 6 mm, 8 mm, and 10 mm. The best cases were identified with a 6 mm PCM thickness, which is better in terms of heat transfer improvement of 6% observed.

Graphical Abstract

An Innovative and Reliable Hybrid Cooling Method for Electric Vehicle Motors

Keywords

Main Subjects

References

  1. Lee K-H, Cha H-R, Kim Y-B. Development of an interior permanent magnet motor through rotor cooling for electric vehicles. Applied Thermal Engineering. 2016;95:348-56. 10.1016/j.applthermaleng.2015.11.022
  2. Bellettre J, Sartre V, Biais F, Lallemand A. Transient state study of electric motor heating and phase change solid-liquid cooling. Applied Thermal Engineering. 1997;17(1):17-31. 10.1016/1359-4311(96)00026-9
  3. Huai Y, Melnik RV, Thogersen PB. Computational analysis of temperature rise phenomena in electric induction motors. Applied Thermal Engineering. 2003;23(7):779-95. 10.1016/S1359-4311(03)00013-9
  4. Boglietti A, Cavagnino A, Staton D, Shanel M, Mueller M, Mejuto C. Evolution and modern approaches for thermal analysis of electrical machines. IEEE Transactions on industrial electronics. 2009;56(3):871-82. 10.1109/TIE.2008.2011622
  5. Hosain ML, Fdhila RB. Air-gap heat transfer in rotating electrical machines: a parametric study. Energy Procedia. 2017;142:4176-81. 10.1016/j.egypro.2017.12.343
  6. Yabiku R, Fialho R, Teran L, Ramos ME, Kawasaki N. Use of thermal network on determining the temperature distribution inside electric motors in steady-state and dynamic conditions. IEEE Transactions on Industry Applications. 2010;46(5):1787-95. 10.1109/TIA.2010.2057398
  7. Cavazzuti M, Gaspari G, Pasquale S, Stalio E. Thermal management of a Formula E electric motor: Analysis and optimization. Applied Thermal Engineering. 2019;157:113733. 10.1016/j.applthermaleng.2019.113733
  8. Kuria J, Hwang P. Investigation of thermal performance of electric vehicle BLDC motor. International journal of mechanical engineering. 2012;1(1):1-17.
  9. SC K, W K, MS K. Cooling performance of 25 kW in-wheel motor for electric vehicles. 2013. 10.1007/s12239-013-0060-9
  10. Kim DG, Kim SC. An analysis study for thermal design of ISG (Integrated Starter & Generator) for hybrid electric vehicle. Transactions of the Korean Society of Automotive Engineers. 2013;21(4):120-7. 10.7467/KSAE.2013.21.5.145
  11. SC K. Thermal Performance of Motor and Inverter in an Integrated Starter Generator System for a Hybrid Electric Vehicle. 2013. 10.3390/en6116102
  12. Nategh S, Huang Z, Krings A, Wallmark O, Leksell M. Thermal modeling of directly cooled electric machines using lumped parameter and limited CFD analysis. IEEE Transactions on Energy Conversion. 2013;28(4):979-90. 10.1109/TEC.2013.2283089
  13. Zhou K, Pries J, Hofmann H. Computationally efficient 3-D finite-element-based dynamic thermal models of electric machines. IEEE Transactions on Transportation Electrification. 2015;1(2):138-49. 10.1109/TTE.2015.2456429
  14. DH L, SC K. Thermal performance of oil spray cooling system for in-wheel motor in electric vehicles. 2014. 10.1016/j.applthermaleng.2013.11.057
  15. Huang J, Naini SS, Miller R, Rizzo D, Sebeck K, Shurin S, et al. A hybrid electric vehicle motor cooling system—design, model, and control. IEEE Transactions on Vehicular Technology. 2019;68(5):4467-78. 10.1109/TVT.2019.2902135
  16. Pechanek R, Bouzek L, editors. Analyzing of two types water cooling electric motors using computational fluid dynamics. 2012 15th International Power Electronics and Motion Control Conference (EPE/PEMC); 2012: IEEE. 10.1109/EPEPEMC.2012.6397424
  17. Li H. Cooling of a permanent magnet electric motor with a centrifugal impeller. International journal of heat and mass transfer. 2010;53(4):797-810. 10.1016/j.ijheatmasstransfer.2009.09.022
  18. Jayakumar S, Sreekanth M. A novel cooling method for electric vehicle motors–a CFD study.
  19. Selvan J, Manavalla S. Numerical Analysis of E-Machine Cooling Using Phase Change Material. Energies. 2022;15(15):5594. 10.3390/en15155594
  20. Durham MO, Lockerd CR. Effect of cyclic loading on motor efficiency. IEEE Transactions on industry applications. 1988;24(6):1153-9. 10.1109/28.17491
  21. Pradeep R, Venugopal T. Experimental study of lithium-ion battery cooling using mixture of phase change materials. International Journal of Electric and Hybrid Vehicles. 2020;12(2):168-83. 10.1504/IJEHV.2020.10027333
  22. Kumar S, Hassan SB, Sharma K, Baheta A. Heat Transfer Coefficients Investigation for TiO2 Based Nanofluids. International Journal of Engineering, Transactions A: Basics. 2019;32(10):1491-6. 10.5829/ije.2019.32.10a.19
International Journal of Engineering
Volume 37, Issue 7
TRANSACTIONS A: Basics
July 2024
Pages 1263-1273

Files

Share

How to cite

Statistics