1. Phul, A.A., Memon, M.J., Shah, S.N.R. and Sandhu, A.R., "Ggbs
and fly ash effects on compressive strength by partial replacement
of cement concrete", Civil Engineering Journal, Vol. 5, No. 4,
(2019), 913-921.
2. Biswas, R. and Rai, B., "Efficiency concepts and models that
evaluates the strength of concretes containing different
supplementary cementitious materials", Civil Engineering
Journal, Vol. 5, No. 1, (2019), 18-32.
3. Fallah, S. and Nematzadeh, M., "Mechanical properties and
durability of high-strength concrete containing macro-polymeric
and polypropylene fibers with nano-silica and silica fume",
Construction and Building Materials, Vol. 132, (2017), 170187.
4. Shannag, M., "High strength concrete containing natural
pozzolan and silica fume", Cement and Concrete Composites,
Vol. 22, No. 6, (2000), 399-406.
5. Çınar, M., Karpuzcu, M. and Çanakcı, H., "Effect of waste marble
powder and fly ash on the rheological characteristics of cement
based grout", Civil Engineering Journal, Vol. 5, No. 4, (2019),
777-788.
6. Gamil, Y., Bakar, I. and Ahmed, K., "Simulation and
development of instrumental setup to be used for cement grouting
of sand soil", Emerging Science Journal, Vol. 1, No. 1, (2017),
16-27.
7. Ekeleme, A.C. and Agunwamba, J.C., "Experimental
determination of dispersion coefficient in soil", Emerging
Science Journal, Vol. 2, No. 4, (2018), 213-218.
8. Sharma, D., Sharma, S. and Goyal, A., "Utilization of waste
foundry slag and alccofine for developing high strength
concrete", International Journal of Electrochemical Science,
Vol. 11, No. 1, (2016), 3190-3205.
9. HS, M.A. and Kshirsagar, S., "Use of alccofine 1203 in concrete
roads", International Journal of Applied Engineering Research,
Vol. 13, No. 7, (2018), 299-301.
10. Singhal, D., Junaid, M.T., Jindal, B.B. and Mehta, A.,
"Mechanical and microstructural properties of fly ash based
geopolymer concrete incorporating alccofine at ambient curing",
Construction and Building Materials, Vol. 180, (2018), 298307.
11. Gupta, A.K., "Experimental study of strength relationship of
concrete cube and concrete cylinder using ultrafine slag
alccofine", International Journal of Scientific & Engineering
Research, vol. 5, (2014), 102–107.
12. Narender Reddy, A. and Meena, T., "An experimental
investigation on mechanical behaviour of eco-friendly concrete",
in Materials Science and Engineering Conference Series. Vol.
263, (2017), 032010.
13. IS, Indian standard ordinary portland cement, 43 grade–
specification, Bureau of Indian Standards, New Delhi, (2003).
14. IS, Indian standard pulverized fuel ash–specification, Bureau of
Indian Standards, New Delhi, (2003).
15. BIS, I., 456 plain and reinforced concrete-code of practice",
Bureau of Indian Standards, New Delhi, (2000).
16. Is:12089-1987, specification for granulated slag for the
manufacture of portland slag cement, Bureau of Indian Standards,
New Delhi, (1987).
17. BIS, Is 383-1970: Specification for coarse and fine aggregate
from natural sources for concrete (second rev.), Bureau of Indian
Standards, New Delhi, (1970).
18. Is:9103-1999, concrete admixture-specifications, Bureau of
Indian Standards, New Delhi, (1999).
19. Is 10262: 2009, concrete mix proportioning guidelines, Bureau of
Indian Standards, New Delhi, (2009).
20. Is:516-2004, “methods of test for strength of concrete, Bureau of
Indian Standards, New Delhi, (2004).
21. –IS, Splitting tensile strength of concrete-method of test. Bureau
of Indian Standards, New Delhi, (1999).
22. Standard, A., C469, 2010,“standard test method for static
modulus of elasticity and poisson’s ratio of concrete in
compression.” astm international, west conshohocken, pa, (2010),
doi: 10.1520/c0469_c0469m-10.
23. ASTM, C., "Standard test method for density, absorption, and
voids in hardened concrete", C642–13, (2013).
24. Is, Methods of sampling and analysis of concrete, Bureau of
Indian Standards, New Delhi, (2004).
25. Mehta, P.K. and Monteiro, P.J., Concrete microstructure,
properties and materials, (2017).
26. Ahmad, S.H. and Shah, S.P., "Structural properties of high
strength concrete and its implications for precast prestressed
concrete", PCI Journal, Vol. 30, No. 6, (1985), 92-119.
27. Oluokun, F., "Prediction of concrete tensile strength from its
compressive strength: An evaluation of existing relations for
normal weight concrete", Materials Journal, Vol. 88, No. 3,
(1991), 302-309.
28. Rashid, M., Mansur, M. and Paramasivam, P., "Correlations
between mechanical properties of high-strength concrete",
Journal of Materials in Civil Engineering, Vol. 14, No. 3,
(2002), 230-238.
29. Bhanja, S. and Sengupta, B., "Influence of silica fume on the
tensile strength of concrete", Cement and concrete research,
Vol. 35, No. 4, (2005), 743-747.
30. Pul, S., "Experimental investigation of tensile behaviour of high
strength concrete", Indian Journal of Engineering and
Materials Sciences, Vol. 15, (2008), 467–472.
31. Perumal, R., "Correlation of compressive strength and other
engineering properties of high-performance steel fiber–reinforced
concrete", Journal of Materials in Civil Engineering, Vol. 27,
No. 1, (2015), 04014114.
32. Chhorn, C., Hong, S.J. and Lee, S.W., "Relationship between
compressive and tensile strengths of roller-compacted concrete",
Journal of Traffic and Transportation Engineering (English
Edition), Vol. 5, No. 3, (2018), 215-223.
33. Zareei, S.A., Ameri, F., Bahrami, N., Shoaei, P., Moosaei, H.R.
and Salemi, N., "Performance of sustainable high strength
concrete with basic oxygen steel-making (BOS) slag and nanosilica",
Journal of Building Engineering, Vol. 25, (2019),
100791.
34. 318, A.C., "Building code requirements for structural concrete
(aci 318-14)[and] commentary on building code requirements for
structural concrete (aci 318r-14), (2014).